2013 Fiat 5 Series power train problems

“The contact owns a 2013 Fiat 500. The contact stated that the vehicle failed to start. The vehicle was towed to the dealer, where it was determined that the shifter cable bushing had failed. The vehicle was repaired under NHTSA Campaign Number: 19V817000 (Power Train); however, the failure recurred 25 miles later. Upon inspection, the contact became aware that the shifter cable bushing under the hood had detached again. The dealer was notified of the failure and informed the contact that the vehicle was repaired with the part provided by the manufacturer. The manufacturer was notified of the failure and initially informed the contact that a case was pending authorization for a loaner vehicle, tow truck service, and repair assistance; however, the dealer later informed the contact that the manufacturer had only agreed to cover the repair. The failure mileage was 117,627.”

“Gear cable broke. Automatic engine could not allow gears to shift. Would like for my vehicle to be included under NHTSA TECALL 19V-817. FCA Campaign Vb4.Fiat 500c 2012-13. MOPAR Fiat case #98205553.”

“Systemic Hydraulic Defect & Safety Recall Circumvention I am reporting a critical safety defect in the clutch hydraulic system of my 2013 Fiat 500 Abarth, which directly mirrors the failures described in NHTSA Recalls 16V-302 and 20V-124. Diagnostic measurements confirm a 1.23mm hydraulic over-travel in the clutch release bearing/slave cylinder assembly. This over-travel causes the diaphragm spring to be over-extended, leading to the catastrophic failure of the pressure plate and subsequent inability to disengage the clutch. This poses an immediate safety risk of vehicle surge or inability to shift gears while in motion. Despite this objective engineering data, Stellantis (FCA US, LLC) Executive offices (specifically Mike Macdonald) have formally refused to perform the safety recall repair, citing my status as the "5th owner" as a justification for exclusion. This represents a willful circumvention of a federal safety recall, as the hydraulic over-travel is a latent design defect present since manufacture and is entirely unrelated to ownership history or vehicle maintenance. The vehicle is currently available for inspection to verify these measurements.”

“While driving 40mph, pressed clutch and the transmission would not shift into gear. Car began to slow in traffic ans I was unable to accelerate as the clutch would not engage a gear. Mamaged to sagely get iff road. No fluid leaks found. Would shift into gear with car off. Gear selection works, not a shift cable issue.”

“2013 FIAT 500 - Manual Transmission. The clutch cover diaphragm spring on the vehicle has fatigue and/or fracture. A failed clutch cover diaphragm spring has resulted in the inability to disengage the clutch, or shift gears. There is an inability to disengage the clutch, shift gears. It is potentially available for inspection if needed. This occurred while driving at low speed (thank goodness). The car became stuck in place when the failure occurred (obviously a safety concern). The issue has been confirmed by a professional. The component has been inspected by service technician. There were no warnings (lamps, messages, etc.). I believe this failure is described in Recall S34 (NHTSA), and this vehicle should be included in that recall. FIAT disagrees and has denied responsibility. Can you help?”

“The contact owns a 2013 Fiat 500. The contact received notification of NHTSA Campaign Number: 16V302000 (POWER TRAIN); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated while driving approximately 30 MPH, the clutch pedal was depressed; however, the pedal was sticking and failed to respond as designed. The contact was almost involved in a crash due to the failure. The contact stated that the vehicle then started operating as needed after the failure. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage 195,000. VIN tool showed no open recall.”