B0005: Driver Frontal Deployment Loop Open
The SRS module detects an open circuit in the driver frontal airbag deployment loop. The airbag will not deploy in a crash and the SRS warning lamp is illuminated.
What B0005 means
B0005 is a generic OBD-II body code in the airbags & restraints group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Warning light or symbol related to the affected system
- Comfort or safety function impaired
Common causes
- 01Clock spring conductor brokenMost likely
- 02Airbag connector unplugged or brokenMost likely
- 03Wiring harness break in steering columnPossible
Can I drive with B0005?
The car drives, but it is a safety risk.
With an airbag or restraint fault stored, one or more airbags or pretensioners may not deploy in a crash. Get it diagnosed soon and do not ignore a lit airbag light.
Why we rate it urgent
- An airbag or seat-belt pretensioner may not work in a crash
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose B0005
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just B0005. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the driver airbag module and clock spring for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Clock spring conductor broken; airbag connector unplugged or broken; wiring harness break in steering column. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
B0005 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Driver airbag module
- Clock spring
- SRS wiring
B0005 FAQ
What does B0005 mean?
B0005 means “Driver Frontal Deployment Loop Open”. The SRS module detects an open circuit in the driver frontal airbag deployment loop. The airbag will not deploy in a crash and the SRS warning lamp is illuminated.
Is B0005 serious? Can I keep driving?
We rate B0005 as urgent severity. The car drives, but it is a safety risk. With an airbag or restraint fault stored, one or more airbags or pretensioners may not deploy in a crash. Get it diagnosed soon and do not ignore a lit airbag light.
What causes B0005?
The most common causes, from most to least likely: Clock spring conductor broken; Airbag connector unplugged or broken; Wiring harness break in steering column. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix B0005?
Typical labor is about $100–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix B0005 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will B0005 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.