B0072: Driver Seatbelt Pretensioner Loop Open
The SRS module detects an open circuit in the driver seatbelt pretensioner deployment loop. The pretensioner cannot fire and the airbag warning lamp is on.
What B0072 means
B0072 is a generic OBD-II body code in the airbags & restraints group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Warning light or symbol related to the affected system
- Comfort or safety function impaired
Common causes
- 01Pretensioner connector unpluggedMost likely
- 02Wire break in B-pillarPossible
Can I drive with B0072?
The car drives, but it is a safety risk.
With an airbag or restraint fault stored, one or more airbags or pretensioners may not deploy in a crash. Get it diagnosed soon and do not ignore a lit airbag light.
Why we rate it urgent
- An airbag or seat-belt pretensioner may not work in a crash
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose B0072
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just B0072. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the driver seatbelt pretensioner and srs seat wiring for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Pretensioner connector unplugged; wire break in B-pillar. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
B0072 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Driver seatbelt pretensioner
- SRS seat wiring
B0072 FAQ
What does B0072 mean?
B0072 means “Driver Seatbelt Pretensioner Loop Open”. The SRS module detects an open circuit in the driver seatbelt pretensioner deployment loop. The pretensioner cannot fire and the airbag warning lamp is on.
Is B0072 serious? Can I keep driving?
We rate B0072 as urgent severity. The car drives, but it is a safety risk. With an airbag or restraint fault stored, one or more airbags or pretensioners may not deploy in a crash. Get it diagnosed soon and do not ignore a lit airbag light.
What causes B0072?
The most common causes, from most to least likely: Pretensioner connector unplugged; Wire break in B-pillar. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix B0072?
Typical labor is about $100–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix B0072 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will B0072 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.