B0103: Front Crash Sensor Left Communication Lost
Communication with the left front crash sensor has been lost; SRS deployment logic for frontal impacts is degraded.
What B0103 means
B0103 is a generic OBD-II body code in the airbags & restraints group.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Warning light or symbol related to the affected system
- Comfort or safety function impaired
Common causes
- 01Open bus wiringMost likely
- 02Gateway module routing CAN messages incorrectlyLess likely
- 03CAN terminating resistor (120 Ω) drifted out of specLess likely
Can I drive with B0103?
Generally yes.
This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
Why we rate it low
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose B0103
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just B0103. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Left front crash sensor, SRS bus) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open bus wiring; gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
B0103 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Left front crash sensor
- SRS bus
B0103 FAQ
What does B0103 mean?
B0103 means “Front Crash Sensor Left Communication Lost”. Communication with the left front crash sensor has been lost; SRS deployment logic for frontal impacts is degraded.
Is B0103 serious? Can I keep driving?
We rate B0103 as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
What causes B0103?
The most common causes, from most to least likely: Open bus wiring; Gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix B0103?
Typical labor is about $75–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix B0103 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will B0103 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.