C0022: ABS Pump Motor Circuit Low
Voltage on the pump motor control line is below threshold. Typical causes are a short to ground or interrupted positive supply.
What C0022 means
C0022 is a generic OBD-II chassis code in the ABS & brakes group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- ABS warning light on
- ESC/stability control deactivated
- Possible reduced brake assist
- Speedometer may behave erratically
Common causes
- 01Wiring shorted to groundMost likely
- 02Pump motor relay failedPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with C0022?
Drive carefully and get it checked soon.
Normal hydraulic braking usually still works, but ABS, stability control or brake assist may be off. Leave extra stopping distance, especially on wet or icy roads. If the pedal feels soft or the red brake light is on, stop driving.
Why we rate it urgent
- ABS or brake assist may be disabled
- Usually lights the ABS, traction or stability warning instead of the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose C0022
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just C0022. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the abs pump motor and pump motor relay for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Wiring shorted to ground; pump motor relay failed; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
C0022 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- ABS pump motor
- Pump motor relay
- Power supply wiring
C0022 FAQ
What does C0022 mean?
C0022 means “ABS Pump Motor Circuit Low”. Voltage on the pump motor control line is below threshold. Typical causes are a short to ground or interrupted positive supply.
Is C0022 serious? Can I keep driving?
We rate C0022 as urgent severity. Drive carefully and get it checked soon. Normal hydraulic braking usually still works, but ABS, stability control or brake assist may be off. Leave extra stopping distance, especially on wet or icy roads. If the pedal feels soft or the red brake light is on, stop driving.
What causes C0022?
The most common causes, from most to least likely: Wiring shorted to ground; Pump motor relay failed; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix C0022?
Typical labor is about $125–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix C0022 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will C0022 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.