C0085: Traction Disable Indicator
Traction control disable indicator lamp circuit fault.
What C0085 means
C0085 is a generic OBD-II chassis code in the stability & traction group.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- ABS warning light on
- ESC/stability control deactivated
- Possible reduced brake assist
- Speedometer may behave erratically
Common causes
- 01Lamp circuit or bulb faultMost likely
Can I drive with C0085?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose C0085
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just C0085. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Tcs off lamp) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Lamp circuit or bulb fault. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
C0085 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Yes, with a scan tool
Basic hand tools; a common first DIY job.
Parts and systems involved
- Tcs off lamp
C0085 FAQ
What does C0085 mean?
C0085 means “Traction Disable Indicator”. Traction control disable indicator lamp circuit fault.
Is C0085 serious? Can I keep driving?
We rate C0085 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes C0085?
The most common causes, from most to least likely: Lamp circuit or bulb fault. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix C0085?
Typical labor is about $15–$65 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix C0085 myself?
DIY difficulty is easy. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will C0085 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.