C05F0: Rear Drive Shaft Speed Sensor Circuit Low
Rear drive shaft speed sensor signal voltage below expected range. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
What C05F0 means
C05F0 is a generic OBD-II chassis code in the ABS & brakes group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- ABS warning light on
- ESC/stability control deactivated
- Possible reduced brake assist
- Speedometer may behave erratically
Common causes
- 01Signal wire shorted to groundMost likely
- 02Connector pins corroded - high contact resistanceLess likely
- 03Harness chafing through insulationLess likely
Can I drive with C05F0?
Not recommended beyond getting it to a shop.
This fault can put the vehicle in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose C05F0
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just C05F0. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the rear drive shaft speed sensor for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Signal wire shorted to ground; connector pins corroded - high contact resistance; harness chafing through insulation. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
C05F0 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Rear drive shaft speed sensor
C05F0 FAQ
What does C05F0 mean?
C05F0 means “Rear Drive Shaft Speed Sensor Circuit Low”. Rear drive shaft speed sensor signal voltage below expected range. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
Is C05F0 serious? Can I keep driving?
We rate C05F0 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the vehicle in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes C05F0?
The most common causes, from most to least likely: Signal wire shorted to ground; Connector pins corroded - high contact resistance; Harness chafing through insulation. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix C05F0?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix C05F0 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will C05F0 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.