C062F: Active Air Dam Supply Voltage Circuit High
Active air dam supply voltage above expected range. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
What C062F means
C062F is a generic OBD-II chassis code in the ABS & brakes group. In plain English: the computer sees a voltage on that circuit that is higher than it should ever be — often an open ground, a short to power, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- ABS warning light on
- ESC/stability control deactivated
- Possible reduced brake assist
- Speedometer may behave erratically
Common causes
- 01Charging system overvoltageMost likely
- 02Connector pins corroded - high contact resistanceLess likely
- 03Supply wire pinched against B+ sourceLess likely
Can I drive with C062F?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose C062F
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just C062F. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the active air dam actuator and alternator for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Charging system overvoltage; connector pins corroded - high contact resistance; supply wire pinched against B+ source. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
C062F repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Active air dam actuator
- Alternator
C062F FAQ
What does C062F mean?
C062F means “Active Air Dam Supply Voltage Circuit High”. Active air dam supply voltage above expected range. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
Is C062F serious? Can I keep driving?
We rate C062F as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes C062F?
The most common causes, from most to least likely: Charging system overvoltage; Connector pins corroded - high contact resistance; Supply wire pinched against B+ source. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix C062F?
Typical labor is about $65–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix C062F myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will C062F clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.