P0137: O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)
The downstream oxygen sensor signal is fixed at a low voltage. Either the catalyst is letting unburned oxygen through (sensor sees lean), the sensor itself is shorted to ground, or the catalyst is so degraded that the downstream signal mirrors a lean upstream condition.
What P0137 means
P0137 is a generic OBD-II powertrain code in the O2 sensors group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor. Bank 1 is the side of the engine with cylinder 1 (inline engines only have bank 1).
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Increased fuel consumption
- Possible rough idle or hesitation
- Failed emissions test
Common causes
- 01Signal wire shorted to groundPossible
- 02Catalyst degraded (often appears before P0420)Possible
- 03Exhaust leak between catalyst and downstream sensorLess likely
Can I drive with P0137?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0137
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0137. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P0131, P0151. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the oxygen sensor downstream and catalytic converter for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Signal wire shorted to ground; catalyst degraded (often appears before P0420); exhaust leak between catalyst and downstream sensor. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P0137 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Oxygen sensor downstream
- Catalytic converter
P0137 FAQ
What does P0137 mean?
P0137 means “O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)”. The downstream oxygen sensor signal is fixed at a low voltage. Either the catalyst is letting unburned oxygen through (sensor sees lean), the sensor itself is shorted to ground, or the catalyst is so degraded that the downstream signal mirrors a lean upstream condition.
Is P0137 serious? Can I keep driving?
We rate P0137 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P0137?
The most common causes, from most to least likely: Signal wire shorted to ground; Catalyst degraded (often appears before P0420); Exhaust leak between catalyst and downstream sensor. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0137?
Typical labor is about $40–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0137 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P0137 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.