P0298: Engine Oil Over Temperature
Engine oil temperature exceeded the safe maximum. Risk of oil breakdown and bearing damage.
What P0298 means
P0298 is a generic OBD-II powertrain code in the cooling group.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Oil cooler failure or low oil levelMost likely
Can I drive with P0298?
No. Stop and let the engine cool.
If the temperature gauge is high or you see steam, pull over and switch off. Driving an overheating engine can warp the head and blow the head gasket.
Why we rate it urgent
- Engine over-temperature can cause head-gasket and engine damage
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0298
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0298. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Oil temp sensor, Oil cooler) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Oil cooler failure or low oil level. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0298 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Oil temp sensor
- Oil cooler
P0298 FAQ
What does P0298 mean?
P0298 means “Engine Oil Over Temperature”. Engine oil temperature exceeded the safe maximum. Risk of oil breakdown and bearing damage.
Is P0298 serious? Can I keep driving?
We rate P0298 as urgent severity. No. Stop and let the engine cool. If the temperature gauge is high or you see steam, pull over and switch off. Driving an overheating engine can warp the head and blow the head gasket.
What causes P0298?
The most common causes, from most to least likely: Oil cooler failure or low oil level. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0298?
Typical labor is about $65–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0298 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P0298 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.