P062C: Internal Control Module Vehicle Speed Performance
An internal self-test in the control module reports a fault in its processing of the "vehicle speed" value. The module computes and cross-checks this value redundantly inside its own processor; when the results disagree, the code sets. It points to a hardware or software fault inside the module itself, not to a defect of the external sensor. Causes are an internal processor or memory fault, corrupted control-module software, or low or disturbed module supply voltage.
What P062C means
P062C is a generic OBD-II powertrain code in the speed, idle & cruise group. In plain English: the signal is within electrical limits but doesn’t make sense compared with other readings, so the part or system isn’t performing as expected.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible limp mode or no-start
- Multiple follow-up faults across modules
- Reset/relearn may be needed after repair
Common causes
- 01Internal software anomalyMost likely
Can I drive with P062C?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P062C
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P062C. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Ecu internal processing, Vehicle speed sensor A) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Internal software anomaly. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P062C repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Ecu internal processing
- Vehicle speed sensor A
P062C FAQ
What does P062C mean?
P062C means “Internal Control Module Vehicle Speed Performance”. An internal self-test in the control module reports a fault in its processing of the "vehicle speed" value. The module computes and cross-checks this value redundantly inside its own processor; when the results disagree, the code sets. It points to a hardware or software fault inside the module itself, not to a defect of the external sensor. Causes are an internal processor or memory fault, corrupted control-module software, or low or disturbed module supply voltage.
Is P062C serious? Can I keep driving?
We rate P062C as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P062C?
The most common causes, from most to least likely: Internal software anomaly. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P062C?
Typical labor is about $250–$1,000 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P062C myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P062C clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.