P06AB: Control Module Internal Temperature Sensor B Circuit
A general circuit fault on the ECU's internal temperature sensor B - the sensor that monitors module operating temperature for thermal protection.
What P06AB means
P06AB is a generic OBD-II powertrain code in the computer & electrical group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible limp mode or no-start
- Multiple follow-up faults across modules
- Reset/relearn may be needed after repair
Common causes
- 01Internal sensor faultMost likely
Can I drive with P06AB?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P06AB
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P06AB. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P0666. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the ecu internal temperature sensor b for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Internal sensor fault. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P06AB repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Ecu internal temperature sensor B
P06AB FAQ
What does P06AB mean?
P06AB means “Control Module Internal Temperature Sensor B Circuit”. A general circuit fault on the ECU's internal temperature sensor B - the sensor that monitors module operating temperature for thermal protection.
Is P06AB serious? Can I keep driving?
We rate P06AB as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P06AB?
The most common causes, from most to least likely: Internal sensor fault. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P06AB?
Typical labor is about $250–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P06AB myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P06AB clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.