P06DB: Engine Oil Pressure Control Circuit Low
Same as P06DA with the control line shorted to ground. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
What P06DB means
P06DB is a generic OBD-II powertrain code in the computer & electrical group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible limp mode or no-start
- Multiple follow-up faults across modules
- Reset/relearn may be needed after repair
Common causes
- 01Control line shorted to groundMost likely
- 02Connector pins corroded - high contact resistanceLess likely
- 03Harness chafing through insulationLess likely
Can I drive with P06DB?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P06DB
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P06DB. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the oil pressure regulator for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Control line shorted to ground; connector pins corroded - high contact resistance; harness chafing through insulation. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P06DB repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Oil pressure regulator
P06DB FAQ
What does P06DB mean?
P06DB means “Engine Oil Pressure Control Circuit Low”. Same as P06DA with the control line shorted to ground. Wiring faults of this kind typically come from chafing, water ingress at connector seals, or pin push-back — a wiggle test on the harness while the code is active often confirms the location.
Is P06DB serious? Can I keep driving?
We rate P06DB as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P06DB?
The most common causes, from most to least likely: Control line shorted to ground; Connector pins corroded - high contact resistance; Harness chafing through insulation. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P06DB?
Typical labor is about $125–$440 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P06DB myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P06DB clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.