P07B2: Transmission Park Position Sensor/Switch A Circuit/Open
Park position sensor/switch A — confirms that the gear selector lever is in Park, used by shift-by-wire systems and key-interlock logic — is open. The TCM cannot confirm Park engagement, blocking key removal and engine restart logic.
What P07B2 means
P07B2 is a generic OBD-II powertrain code in the transmission group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine or transmission warning light on
- Harsh, delayed, or missing shifts
- Possible limp mode (locked in one gear)
- Slipping or shuddering during gear changes
Common causes
- 01Open wire or unplugged sensorMost likely
- 02Pin pushed back out of connector bodyLess likely
- 03Cracked solder joint inside the module or sensorLess likely
Can I drive with P07B2?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P07B2
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P07B2. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P07B8. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the park position sensor a and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open wire or unplugged sensor; pin pushed back out of connector body; cracked solder joint inside the module or sensor. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P07B2 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Park position sensor A
- Wiring harness
P07B2 FAQ
What does P07B2 mean?
P07B2 means “Transmission Park Position Sensor/Switch A Circuit/Open”. Park position sensor/switch A — confirms that the gear selector lever is in Park, used by shift-by-wire systems and key-interlock logic — is open. The TCM cannot confirm Park engagement, blocking key removal and engine restart logic.
Is P07B2 serious? Can I keep driving?
We rate P07B2 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P07B2?
The most common causes, from most to least likely: Open wire or unplugged sensor; Pin pushed back out of connector body; Cracked solder joint inside the module or sensor. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P07B2?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P07B2 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P07B2 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.