P0AAE: Hybrid/EV Battery Pack Air Temperature Sensor A Circuit Low
The ECM detects a circuit low fault on the hybrid/ev battery pack air temperature sensor a circuit. Reading cannot be used reliably for control.
What P0AAE means
P0AAE is a generic OBD-II powertrain code in the hybrid & EV group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- EV/hybrid system warning light on
- Reduced power output or limp mode
- Charging may fail or be slowed
- Reduced electric range
Common causes
- 01Signal wire shorted to groundMost likely
- 02Internal sensor shortPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with P0AAE?
Have it checked before relying on the car.
High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
Why we rate it urgent
- High-voltage system fault: the car may shut down or refuse to start
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0AAE
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0AAE. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P0AB3. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the high-voltage battery pack air temp sensor a and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Signal wire shorted to ground; internal sensor short; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0AAE repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Usually a shop job
Basic hand tools; a common first DIY job.
Parts and systems involved
- High-voltage battery pack air temp sensor A
- Wiring harness
- BMS
P0AAE FAQ
What does P0AAE mean?
P0AAE means “Hybrid/EV Battery Pack Air Temperature Sensor A Circuit Low”. The ECM detects a circuit low fault on the hybrid/ev battery pack air temperature sensor a circuit. Reading cannot be used reliably for control.
Is P0AAE serious? Can I keep driving?
We rate P0AAE as urgent severity. Have it checked before relying on the car. High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
What causes P0AAE?
The most common causes, from most to least likely: Signal wire shorted to ground; Internal sensor short; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0AAE?
Typical labor is about $65–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0AAE myself?
DIY difficulty is easy. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P0AAE clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.