P0CC8: Charge Port Door A Open Request Switch Circuit Performance
The charge port door A open request switch circuit performance reports a fault. Operator request for charge port unlocking is unreliable.
What P0CC8 means
P0CC8 is a generic OBD-II powertrain code in the hybrid & EV group. In plain English: the signal is within electrical limits but doesn’t make sense compared with other readings, so the part or system isn’t performing as expected.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Charge status indicator shows fault
- Charging may not start or interrupts
- Slower-than-expected charge rate
Common causes
- 01Switch contacts agedMost likely
- 02High-resistance contactPossible
Can I drive with P0CC8?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0CC8
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0CC8. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P2E94. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the charge port door a request switch and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Switch contacts aged; high-resistance contact. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0CC8 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Yes, with a scan tool
Basic hand tools; a common first DIY job.
Parts and systems involved
- Charge port door A request switch
- Wiring harness
- BMS
P0CC8 FAQ
What does P0CC8 mean?
P0CC8 means “Charge Port Door A Open Request Switch Circuit Performance”. The charge port door A open request switch circuit performance reports a fault. Operator request for charge port unlocking is unreliable.
Is P0CC8 serious? Can I keep driving?
We rate P0CC8 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P0CC8?
The most common causes, from most to least likely: Switch contacts aged; High-resistance contact. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0CC8?
Typical labor is about $40–$190 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0CC8 myself?
DIY difficulty is easy. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P0CC8 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.