P0E98: Drive Motor B Inverter Voltage Sensor B Circuit Intermittent/Erratic
The ECM detects a intermittent/erratic fault on the drive motor b inverter voltage sensor b circuit. Reading cannot be used reliably for control.
What P0E98 means
P0E98 is a generic OBD-II powertrain code in the hybrid & EV group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- EV/hybrid system warning light on
- Reduced motor power or torque
- Possible limp mode or vehicle shutdown
Common causes
- 01Sensor connector not seatedMost likely
- 02Noisy ground referencePossible
- 03Connector with intermittent contact under vibrationLess likely
Can I drive with P0E98?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0E98
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0E98. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P0E93, P0DA7, P0D31. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the drive motor b inverter voltage sensor b and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Sensor connector not seated; noisy ground reference; connector with intermittent contact under vibration. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0E98 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Drive motor B inverter voltage sensor B
- Wiring harness
- Hybrid control module
P0E98 FAQ
What does P0E98 mean?
P0E98 means “Drive Motor B Inverter Voltage Sensor B Circuit Intermittent/Erratic”. The ECM detects a intermittent/erratic fault on the drive motor b inverter voltage sensor b circuit. Reading cannot be used reliably for control.
Is P0E98 serious? Can I keep driving?
We rate P0E98 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes P0E98?
The most common causes, from most to least likely: Sensor connector not seated; Noisy ground reference; Connector with intermittent contact under vibration. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0E98?
Typical labor is about $125–$625 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0E98 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P0E98 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.