P200F: Catalyst System Over Temperature (Bank 2)
A temperature sensor in the exhaust catalyst on bank 2 reports a value above the safe operating limit. Sustained over-temperature can sinter the precious-metal washcoat and destroy conversion efficiency.
What P200F means
P200F is a generic OBD-II powertrain code in the emissions group. Bank 2 is the side of a V or flat engine opposite cylinder 1.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Failed emissions inspection
- Possibly slightly increased fuel consumption
- Sulfur (rotten egg) smell from exhaust under load
Common causes
- 01Misfire dumps fuel into catMost likely
Can I drive with P200F?
No. Stop and let the engine cool.
If the temperature gauge is high or you see steam, pull over and switch off. Driving an overheating engine can warp the head and blow the head gasket.
Why we rate it urgent
- Engine over-temperature can cause head-gasket and engine damage
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P200F
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P200F. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P200E. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Compare upstream and downstream O2 sensors
With the engine warm, the upstream sensor should switch rapidly while the downstream one stays fairly steady. A downstream signal that mirrors the upstream one points to a worn catalyst; check for exhaust leaks and misfires first.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Misfire dumps fuel into cat. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P200F repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Catalytic converter
- Exhaust temperature sensor
P200F FAQ
What does P200F mean?
P200F means “Catalyst System Over Temperature (Bank 2)”. A temperature sensor in the exhaust catalyst on bank 2 reports a value above the safe operating limit. Sustained over-temperature can sinter the precious-metal washcoat and destroy conversion efficiency.
Is P200F serious? Can I keep driving?
We rate P200F as urgent severity. No. Stop and let the engine cool. If the temperature gauge is high or you see steam, pull over and switch off. Driving an overheating engine can warp the head and blow the head gasket.
What causes P200F?
The most common causes, from most to least likely: Misfire dumps fuel into cat. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P200F?
Typical labor is about $125–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P200F myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P200F clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.