P237C: Exhaust Heat Exchanger Bypass Valve A Control Circuit Open
Exhaust Heat Exchanger Bypass Valve A Control Circuit Open: the control circuit is open. Likely a broken wire, disconnected connector, or failed actuator.
What P237C means
P237C is a generic OBD-II powertrain code in the misfire & ignition group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Open in harness or connectorMost likely
- 02Actuator solenoid or motor winding openPossible
- 03Pin pushed back out of connector bodyLess likely
Can I drive with P237C?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P237C
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P237C. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P23A2. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the exhaust heat exchanger and exhaust bypass valve a for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open in harness or connector; actuator solenoid or motor winding open; pin pushed back out of connector body. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P237C repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Exhaust heat exchanger
- Exhaust bypass valve A
- Exhaust heat recovery actuator
P237C FAQ
What does P237C mean?
P237C means “Exhaust Heat Exchanger Bypass Valve A Control Circuit Open”. Exhaust Heat Exchanger Bypass Valve A Control Circuit Open: the control circuit is open. Likely a broken wire, disconnected connector, or failed actuator.
Is P237C serious? Can I keep driving?
We rate P237C as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P237C?
The most common causes, from most to least likely: Open in harness or connector; Actuator solenoid or motor winding open; Pin pushed back out of connector body. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P237C?
Typical labor is about $125–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P237C myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P237C clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.