P240A: EVAP System Leak Detection Pump Heater Control Circuit Open
The leak detection pump heater - keeps the pump diaphragm warm in cold weather - has an open control circuit.
What P240A means
P240A is a generic OBD-II powertrain code in the emissions group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible smell of fuel near tank or engine bay
- Failed emissions inspection
- Loose-cap warning may appear
Common causes
- 01Open in heater or wiringMost likely
- 02Pin pushed back out of connector bodyLess likely
- 03Cracked solder joint inside the module or sensorLess likely
Can I drive with P240A?
Generally yes.
This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
Why we rate it low
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- EVAP leaks rarely affect how the car drives
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P240A
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P240A. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the evap leak detection pump heater for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open in heater or wiring; pin pushed back out of connector body; cracked solder joint inside the module or sensor. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P240A repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- EVAP leak detection pump heater
P240A FAQ
What does P240A mean?
P240A means “EVAP System Leak Detection Pump Heater Control Circuit Open”. The leak detection pump heater - keeps the pump diaphragm warm in cold weather - has an open control circuit.
Is P240A serious? Can I keep driving?
We rate P240A as low severity. Generally yes. This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
What causes P240A?
The most common causes, from most to least likely: Open in heater or wiring; Pin pushed back out of connector body; Cracked solder joint inside the module or sensor. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P240A?
Typical labor is about $65–$225 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P240A myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P240A clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.