P244F: Exhaust Temperature Too High For Particulate Filter Regeneration Bank 2
Same as P244D on bank 2.
What P244F means
P244F is a generic OBD-II powertrain code in the emissions group. Bank 2 is the side of a V or flat engine opposite cylinder 1.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light or DPF warning light on
- Power loss / limp mode
- Increased fuel consumption
- Failed forced regeneration attempts
Common causes
- 01Engine load too high - filter overheating riskMost likely
Can I drive with P244F?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P244F
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P244F. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P244D. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the dpf bank 2 for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Engine load too high - filter overheating risk. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P244F repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- DPF bank 2
P244F FAQ
What does P244F mean?
P244F means “Exhaust Temperature Too High For Particulate Filter Regeneration Bank 2”. Same as P244D on bank 2.
Is P244F serious? Can I keep driving?
We rate P244F as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P244F?
The most common causes, from most to least likely: Engine load too high - filter overheating risk. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P244F?
Typical labor is about $40–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P244F myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P244F clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.