P2464: Diesel Particulate Filter Differential Pressure Too High
The differential pressure across the DPF exceeds the calibrated upper threshold during operation. Indicates severe blockage of the filter element.
What P2464 means
P2464 is a generic OBD-II powertrain code in the emissions group.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Yes
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light or DPF warning light on
- Power loss / limp mode
- Increased fuel consumption
- Failed forced regeneration attempts
Common causes
- 01DPF heavily cloggedMost likely
- 02Blocked pressure sensing lineLess likely
Can I drive with P2464?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2464
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2464. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the diesel particulate filter and dpf diff pressure sensor for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: DPF heavily clogged; blocked pressure sensing line. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2464 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Diesel particulate filter
- DPF diff pressure sensor
- DPF pressure lines
P2464 FAQ
What does P2464 mean?
P2464 means “Diesel Particulate Filter Differential Pressure Too High”. The differential pressure across the DPF exceeds the calibrated upper threshold during operation. Indicates severe blockage of the filter element.
Is P2464 serious? Can I keep driving?
We rate P2464 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes P2464?
The most common causes, from most to least likely: DPF heavily clogged; Blocked pressure sensing line. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2464?
Typical labor is about $190–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2464 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P2464 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.