P24EA: NH3 Sensor Supply Voltage Circuit
The supply rail that powers the NH3 slip sensor electronics (typically 5 V or 12 V from the dosing/SCR module) is out of tolerance. Without a stable supply the sensor cannot deliver a valid ammonia reading, and the ECM disables the closed-loop SCR strategy.
What P24EA means
P24EA is a generic OBD-II powertrain code in the emissions group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Open or shorted supply wireMost likely
- 02Failing supply rail inside the dosing modulePossible
Can I drive with P24EA?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P24EA
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P24EA. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the nh3 sensor and supply wiring for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open or shorted supply wire; failing supply rail inside the dosing module. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P24EA repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- NH3 sensor
- Supply wiring
- Dosing module
P24EA FAQ
What does P24EA mean?
P24EA means “NH3 Sensor Supply Voltage Circuit”. The supply rail that powers the NH3 slip sensor electronics (typically 5 V or 12 V from the dosing/SCR module) is out of tolerance. Without a stable supply the sensor cannot deliver a valid ammonia reading, and the ECM disables the closed-loop SCR strategy.
Is P24EA serious? Can I keep driving?
We rate P24EA as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P24EA?
The most common causes, from most to least likely: Open or shorted supply wire; Failing supply rail inside the dosing module. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P24EA?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P24EA myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P24EA clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.