P2544: Torque Management Request Input Signal A
The ECU detects an invalid torque-management request signal A from another control unit (e.g. transmission, ESP, ABS) on the CAN bus. Cooperative torque control cannot be performed as expected.
What P2544 means
P2544 is a generic OBD-II powertrain code in the speed, idle & cruise group.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01CAN communication errorMost likely
- 02Fault in requesting modulePossible
Can I drive with P2544?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2544
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2544. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P2548. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check live data
Watch the related sensor and actuator readings in live data (CAN bus, TCM, ABS module) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: CAN communication error; fault in requesting module. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P2544 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- CAN bus
- TCM
- ABS module
P2544 FAQ
What does P2544 mean?
P2544 means “Torque Management Request Input Signal A”. The ECU detects an invalid torque-management request signal A from another control unit (e.g. transmission, ESP, ABS) on the CAN bus. Cooperative torque control cannot be performed as expected.
Is P2544 serious? Can I keep driving?
We rate P2544 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes P2544?
The most common causes, from most to least likely: CAN communication error; Fault in requesting module. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2544?
Typical labor is about $125–$625 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2544 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P2544 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.