P25CC: Intake Camshaft Actuator Park Lock Control Circuit High Bank 1
The intake camshaft park-lock control line on bank 1 is above the expected voltage window. Typical causes are a short to battery or a stuck-on driver in the controller.
What P25CC means
P25CC is a generic OBD-II powertrain code in the transmission group. In plain English: the computer sees a voltage on that circuit that is higher than it should ever be — often an open ground, a short to power, or a failed sensor. Bank 1 is the side of the engine with cylinder 1 (inline engines only have bank 1).
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Power loss especially in mid-rpm range
- Possible rough idle or stalling
- Increased fuel consumption
Common causes
- 01Control wire shorted to a B+ supplyMost likely
- 02ECU output driver stuck onPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with P25CC?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P25CC
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P25CC. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P25CF. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the intake cam phaser bank 1 and park lock solenoid for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Control wire shorted to a B+ supply; ECU output driver stuck on; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P25CC repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Intake cam phaser bank 1
- Park lock solenoid
- Wiring harness
P25CC FAQ
What does P25CC mean?
P25CC means “Intake Camshaft Actuator Park Lock Control Circuit High Bank 1”. The intake camshaft park-lock control line on bank 1 is above the expected voltage window. Typical causes are a short to battery or a stuck-on driver in the controller.
Is P25CC serious? Can I keep driving?
We rate P25CC as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P25CC?
The most common causes, from most to least likely: Control wire shorted to a B+ supply; ECU output driver stuck on; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P25CC?
Typical labor is about $125–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P25CC myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P25CC clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.