P2614: Camshaft Position Output Circuit/Open
The camshaft position output signal sent from the ECU to other modules is interrupted. Other systems that rely on the cam reference (e.g. transmission, hybrid module) do not receive a valid signal.
What P2614 means
P2614 is a generic OBD-II powertrain code in the timing, cam & crank group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Power loss especially in mid-rpm range
- Possible rough idle or stalling
- Increased fuel consumption
Common causes
- 01Open output wiringMost likely
- 02Internal ECU output driver faultLess likely
- 03Pin pushed back out of connector bodyLess likely
Can I drive with P2614?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2614
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2614. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the camshaft position sensor and cmp signal wiring for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open output wiring; internal ECU output driver fault; pin pushed back out of connector body. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2614 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Camshaft position sensor
- Cmp signal wiring
P2614 FAQ
What does P2614 mean?
P2614 means “Camshaft Position Output Circuit/Open”. The camshaft position output signal sent from the ECU to other modules is interrupted. Other systems that rely on the cam reference (e.g. transmission, hybrid module) do not receive a valid signal.
Is P2614 serious? Can I keep driving?
We rate P2614 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P2614?
The most common causes, from most to least likely: Open output wiring; Internal ECU output driver fault; Pin pushed back out of connector body. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2614?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2614 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P2614 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.