P2685: Actuator Supply Voltage C Circuit Low
The third actuator supply rail is below the expected voltage. Battery weakness, blown fuse, or excessive current draw collapses the supply.
What P2685 means
P2685 is a generic OBD-II powertrain code in the computer & electrical group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Load on the rail shorted to groundMost likely
- 02Battery condition causes voltage to dropPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with P2685?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2685
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2685. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P2670, P26E8, P0658. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the actuator supply c and charging system for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Load on the rail shorted to ground; battery condition causes voltage to drop; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P2685 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Actuator supply C
- Charging system
P2685 FAQ
What does P2685 mean?
P2685 means “Actuator Supply Voltage C Circuit Low”. The third actuator supply rail is below the expected voltage. Battery weakness, blown fuse, or excessive current draw collapses the supply.
Is P2685 serious? Can I keep driving?
We rate P2685 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P2685?
The most common causes, from most to least likely: Load on the rail shorted to ground; Battery condition causes voltage to drop; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2685?
Typical labor is about $65–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2685 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P2685 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.