P27ED: Transmission Range Control A Position Sensor/Switch Circuit Low
The position sensor or switch of transmission range control channel A reports a circuit low condition. The TCM cannot verify the actuator position reliably.
What P27ED means
P27ED is a generic OBD-II powertrain code in the transmission group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine or transmission warning light on
- Harsh, delayed, or missing shifts
- Possible limp mode (locked in one gear)
- Slipping or shuddering during gear changes
Common causes
- 01Signal wire shorted to groundMost likely
- 02Internal short in position sensorPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with P27ED?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P27ED
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P27ED. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P27F1. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the range control position sensor a and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Signal wire shorted to ground; internal short in position sensor; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P27ED repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Range control position sensor A
- Wiring harness
- TCM
P27ED FAQ
What does P27ED mean?
P27ED means “Transmission Range Control A Position Sensor/Switch Circuit Low”. The position sensor or switch of transmission range control channel A reports a circuit low condition. The TCM cannot verify the actuator position reliably.
Is P27ED serious? Can I keep driving?
We rate P27ED as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes P27ED?
The most common causes, from most to least likely: Signal wire shorted to ground; Internal short in position sensor; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P27ED?
Typical labor is about $125–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P27ED myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P27ED clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.