P288D: Shift Fork B Calibration Not Learned
The TCM has not learned the end-stop calibration for shift fork B. Engagement positions cannot be commanded with full precision until adaptation completes.
What P288D means
P288D is a generic OBD-II powertrain code in the transmission group.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine or transmission warning light on
- Harsh, delayed, or missing shifts
- Possible limp mode (locked in one gear)
- Slipping or shuddering during gear changes
Common causes
- 01Adaptation lost after battery disconnect or TCM resetMost likely
- 02Shift fork replaced without learn procedurePossible
Can I drive with P288D?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P288D
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P288D. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P287B. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Shift fork B, Shift fork actuator B, TCM) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Adaptation lost after battery disconnect or TCM reset; shift fork replaced without learn procedure. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P288D repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Usually a shop job
Basic hand tools; a common first DIY job.
Parts and systems involved
- Shift fork B
- Shift fork actuator B
- TCM
P288D FAQ
What does P288D mean?
P288D means “Shift Fork B Calibration Not Learned”. The TCM has not learned the end-stop calibration for shift fork B. Engagement positions cannot be commanded with full precision until adaptation completes.
Is P288D serious? Can I keep driving?
We rate P288D as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P288D?
The most common causes, from most to least likely: Adaptation lost after battery disconnect or TCM reset; Shift fork replaced without learn procedure. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P288D?
Typical labor is about $40–$190 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P288D myself?
DIY difficulty is easy. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P288D clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.