P2B7C: EVAP System Pressure Sensor/Switch C Circuit Low
The EVAP pressure sensor/switch C reports a circuit low condition. Tank pressure plausibility for leak detection on this branch is impaired.
What P2B7C means
P2B7C is a generic OBD-II powertrain code in the emissions group. In plain English: the computer sees a voltage on that circuit that is lower than it should ever be — often a short to ground, an open, or a failed sensor.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible smell of fuel near tank or engine bay
- Failed emissions inspection
- Loose-cap warning may appear
Common causes
- 01Signal wire shorted to groundMost likely
- 02Internal sensor shortPossible
- 03Connector pins corroded - high contact resistanceLess likely
Can I drive with P2B7C?
Generally yes.
This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
Why we rate it low
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- EVAP leaks rarely affect how the car drives
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2B7C
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2B7C. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the evap pressure sensor c and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Signal wire shorted to ground; internal sensor short; connector pins corroded - high contact resistance. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2B7C repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Yes, with a scan tool
Basic hand tools; a common first DIY job.
Parts and systems involved
- EVAP pressure sensor C
- Wiring harness
- ECM
P2B7C FAQ
What does P2B7C mean?
P2B7C means “EVAP System Pressure Sensor/Switch C Circuit Low”. The EVAP pressure sensor/switch C reports a circuit low condition. Tank pressure plausibility for leak detection on this branch is impaired.
Is P2B7C serious? Can I keep driving?
We rate P2B7C as low severity. Generally yes. This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
What causes P2B7C?
The most common causes, from most to least likely: Signal wire shorted to ground; Internal sensor short; Connector pins corroded - high contact resistance. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2B7C?
Typical labor is about $40–$190 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2B7C myself?
DIY difficulty is easy. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P2B7C clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.