P2DD9: EVAP System Leak Detection Pump Control Circuit Performance
The EVAP leak detection pump control circuit reports a performance condition. Pump response or current draw outside calibration.
What P2DD9 means
P2DD9 is a generic OBD-II powertrain code in the emissions group. In plain English: the signal is within electrical limits but doesn’t make sense compared with other readings, so the part or system isn’t performing as expected.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible smell of fuel near tank or engine bay
- Failed emissions inspection
- Loose-cap warning may appear
Common causes
- 01Pump output degradedMost likely
- 02High-resistance contactPossible
Can I drive with P2DD9?
Generally yes.
This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
Why we rate it low
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- EVAP leaks rarely affect how the car drives
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2DD9
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2DD9. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the evap leak detection pump and wiring harness for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Pump output degraded; high-resistance contact. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2DD9 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- EVAP leak detection pump
- Wiring harness
- ECM
P2DD9 FAQ
What does P2DD9 mean?
P2DD9 means “EVAP System Leak Detection Pump Control Circuit Performance”. The EVAP leak detection pump control circuit reports a performance condition. Pump response or current draw outside calibration.
Is P2DD9 serious? Can I keep driving?
We rate P2DD9 as low severity. Generally yes. This fault is unlikely to affect how the car drives, but it will usually fail an emissions inspection. Fix it when convenient.
What causes P2DD9?
The most common causes, from most to least likely: Pump output degraded; High-resistance contact. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2DD9?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2DD9 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P2DD9 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.