P3472: Cylinder Deactivation Hydraulic Circuit Bank 2 Low
The engine control module has detected low oil pressure in the bank 2 hydraulic circuit responsible for cylinder deactivation. Below the calibrated threshold the switching lifters cannot collapse and cylinder deactivation on bank 2 is disabled until pressure recovers.
What P3472 means
P3472 is a generic OBD-II powertrain code in the timing, cam & crank group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component. Bank 2 is the side of a V or flat engine opposite cylinder 1.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Low engine oil levelMost likely
- 02Oil pump worn or weakPossible
- 03Oil pressure switch reads lowPossible
Can I drive with P3472?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P3472
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P3472. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P3468. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the oil pump and oil control valve for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Low engine oil level; oil pump worn or weak; oil pressure switch reads low. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P3472 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Oil pump
- Oil control valve
- Oil pressure switch
P3472 FAQ
What does P3472 mean?
P3472 means “Cylinder Deactivation Hydraulic Circuit Bank 2 Low”. The engine control module has detected low oil pressure in the bank 2 hydraulic circuit responsible for cylinder deactivation. Below the calibrated threshold the switching lifters cannot collapse and cylinder deactivation on bank 2 is disabled until pressure recovers.
Is P3472 serious? Can I keep driving?
We rate P3472 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P3472?
The most common causes, from most to least likely: Low engine oil level; Oil pump worn or weak; Oil pressure switch reads low. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P3472?
Typical labor is about $190–$1,000 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P3472 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P3472 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.