U0106: Lost Communication with Glow Plug Control Module
The Glow Plug Control Module has stopped transmitting on the vehicle data bus, so other control units no longer receive its messages. Cold-start pre-heating is no longer coordinated, causing hard diesel starts. Typical causes are loss of power or ground at the module, an open or shorted CAN/LIN bus wire, a connector fault, or an internal module failure.
What U0106 means
U0106 is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Glow Plug Control Module on the vehicle’s data network.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Glow plug module unpoweredMost likely
- 02CAN wiring to glow plug module brokenPossible
- 03Gateway module routing CAN messages incorrectlyLess likely
Can I drive with U0106?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U0106
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U0106. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Glow plug module unpowered; CAN wiring to glow plug module broken; gateway module routing CAN messages incorrectly. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
U0106 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Glow plug control module
- CAN bus wiring
U0106 FAQ
What does U0106 mean?
U0106 means “Lost Communication with Glow Plug Control Module”. The Glow Plug Control Module has stopped transmitting on the vehicle data bus, so other control units no longer receive its messages. Cold-start pre-heating is no longer coordinated, causing hard diesel starts. Typical causes are loss of power or ground at the module, an open or shorted CAN/LIN bus wire, a connector fault, or an internal module failure.
Is U0106 serious? Can I keep driving?
We rate U0106 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes U0106?
The most common causes, from most to least likely: Glow plug module unpowered; CAN wiring to glow plug module broken; Gateway module routing CAN messages incorrectly. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U0106?
Typical labor is about $125–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U0106 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U0106 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.