U014B: Lost Communication With Hybrid/EV Battery Inductive Charging Module
ECU lost CAN communication with the inductive charging module (wireless charging of HV battery). A communication loss with this module breaks any function relying on its data — diagnostic tools may show 'no response' and dependent modules can fall into limp mode.
What U014B means
U014B is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Hybrid/EV Battery Inductive Charging Module on the vehicle’s data network.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Module unpoweredMost likely
- 02Gateway module routing CAN messages incorrectlyLess likely
- 03CAN terminating resistor (120 Ω) drifted out of specLess likely
Can I drive with U014B?
Have it checked before relying on the car.
High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
Why we rate it urgent
- High-voltage system fault: the car may shut down or refuse to start
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U014B
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U014B. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Module unpowered; gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
U014B repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Inductive charging module
- CAN bus
U014B FAQ
What does U014B mean?
U014B means “Lost Communication With Hybrid/EV Battery Inductive Charging Module”. ECU lost CAN communication with the inductive charging module (wireless charging of HV battery). A communication loss with this module breaks any function relying on its data — diagnostic tools may show 'no response' and dependent modules can fall into limp mode.
Is U014B serious? Can I keep driving?
We rate U014B as urgent severity. Have it checked before relying on the car. High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
What causes U014B?
The most common causes, from most to least likely: Module unpowered; Gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U014B?
Typical labor is about $125–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U014B myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U014B clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.