U0192Network · Lost communicationGeneric (SAE) code

U0192: Lost Communication with Personal Computer

The vehicle gateway has lost the on-board computer / fleet telematics PC. Logging, fleet management or driver-assistance based on the PC stop working.

Typical labor cost
$40–$250 est.
18 min–2 h at an assumed $125/hr · parts extra · use your rate
Most common fix
PC unpowered or hung
DIY difficulty: Moderate · usually a shop job
01 —What it means

What U0192 means

U0192 is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Personal Computer on the vehicle’s data network.

U
Network
0
Generic (SAE)
1
Subsystem group
92
Specific fault
How to read U0192. We group it under Lost communication.
Check engine light
Usually off
Emissions-related
No
Limp mode possible
Not typical
Drive cycle to clear
Not required
Code data: OBDex (CC0)

Get it fixed

Post this code once and get quotes from local mechanics. Free to post.

Your car Optional

Makes the repair and parts links below specific to your car. Kept in this browser only.

Get quotes on findmechanic.ai (opens in a new tab)
02 —Symptoms

Symptoms

What drivers typically notice
  • Multiple warning lights may illuminate
  • Affected modules may go into limp mode or shut down
  • Specific functions inoperative depending on module
  • Diagnostic tools may show communication faults
Code data: OBDex (CC0)
03 —Causes

Common causes

Ranked from most to least likely
  1. 01PC unpowered or hungMost likely
  2. 02Gateway module routing CAN messages incorrectlyLess likely
  3. 03CAN terminating resistor (120 Ω) drifted out of specLess likely
Code data: OBDex (CC0)
04 —Severity

Can I drive with U0192?

Low

Generally yes.

This fault is unlikely to affect how the car drives. Fix it when convenient.

Why we rate it low

  • Does not normally turn on the check engine light

Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.

Code data: OBDex (CC0)
05 —Diagnosis

How to diagnose U0192

General procedure — follow the service manual for your vehicle
  1. 1

    Confirm the code and save freeze-frame data

    Read the codes with an OBD-II scan tool and note every code, not just U0192. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.

  2. 2

    Fix other faults first

    If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.

  3. 3

    Check module power, ground and the data bus

    Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.

  4. 4

    Test the likely causes in order

    Start with the most likely cause and work down: PC unpowered or hung; gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts.

  5. 5

    Check for recalls and service bulletins

    Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.

  6. 6

    Clear the code and verify the repair

    After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.

Code data: OBDex (CC0)
06 —Cost

U0192 repair cost estimate

Labor only — set your local shop rate
Labor estimate for U0192
$40–$250
18 min–2 h of labor × $125/hr (assumed rate) · parts extra

Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.

DIY difficulty
Moderate
Good DIY job?
Usually a shop job

Needs a scan tool and some experience with testing.

Code data: OBDex (CC0)
07 —Components

Parts and systems involved

  • Onboard pc
  • CAN bus wiring
Code data: OBDex (CC0)
09 —FAQ

U0192 FAQ

What does U0192 mean?

U0192 means “Lost Communication with Personal Computer”. The vehicle gateway has lost the on-board computer / fleet telematics PC. Logging, fleet management or driver-assistance based on the PC stop working.

Is U0192 serious? Can I keep driving?

We rate U0192 as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient.

What causes U0192?

The most common causes, from most to least likely: PC unpowered or hung; Gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts, because several causes can set the same code.

How much does it cost to fix U0192?

Typical labor is about $40–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.

Can I fix U0192 myself?

DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.

Will U0192 clear itself?

If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.

Code data: OBDex (CC0)