U0295: Lost Communication with Power Steering Control Module
The vehicle network has lost the electric power steering (EPS) control module. Power assist drops out, the steering becomes heavy and the EPS warning lamp lights up.
What U0295 means
U0295 is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Power Steering Control Module on the vehicle’s data network.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01EPS module unpoweredMost likely
- 02CAN wiring to EPS damagedPossible
- 03Gateway module routing CAN messages incorrectlyLess likely
Can I drive with U0295?
Drive carefully and get it checked soon.
Steering assist may drop out, making the wheel heavy at low speed. Avoid driving if steering becomes very heavy or erratic.
Why we rate it urgent
- Steering assist may be reduced or lost
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U0295
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U0295. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for U0131. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: EPS module unpowered; CAN wiring to EPS damaged; gateway module routing CAN messages incorrectly. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
U0295 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- EPS module
- CAN bus wiring
U0295 FAQ
What does U0295 mean?
U0295 means “Lost Communication with Power Steering Control Module”. The vehicle network has lost the electric power steering (EPS) control module. Power assist drops out, the steering becomes heavy and the EPS warning lamp lights up.
Is U0295 serious? Can I keep driving?
We rate U0295 as urgent severity. Drive carefully and get it checked soon. Steering assist may drop out, making the wheel heavy at low speed. Avoid driving if steering becomes very heavy or erratic.
What causes U0295?
The most common causes, from most to least likely: EPS module unpowered; CAN wiring to EPS damaged; Gateway module routing CAN messages incorrectly. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U0295?
Typical labor is about $65–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U0295 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U0295 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.