U0402: Invalid Data Received from TCM
A control module is communicating with the transmission control module but receives implausible data — wrong checksum, frozen value, or out-of-range value. Often results in transmission limp-home.
What U0402 means
U0402 is a generic OBD-II network code in the invalid data & software group. In plain English: a module received data that didn’t make sense from the TCM.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01TCM software bug or outdated calibrationPossible
- 02TCM internal sensor or processing faultPossible
- 03CAN corruption causing checksum errorsPossible
Can I drive with U0402?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U0402
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U0402. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: TCM software bug or outdated calibration; TCM internal sensor or processing fault; CAN corruption causing checksum errors. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
U0402 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- TCM
- CAN bus wiring
U0402 FAQ
What does U0402 mean?
U0402 means “Invalid Data Received from TCM”. A control module is communicating with the transmission control module but receives implausible data — wrong checksum, frozen value, or out-of-range value. Often results in transmission limp-home.
Is U0402 serious? Can I keep driving?
We rate U0402 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes U0402?
The most common causes, from most to least likely: TCM software bug or outdated calibration; TCM internal sensor or processing fault; CAN corruption causing checksum errors. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U0402?
Typical labor is about $125–$625 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U0402 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U0402 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.