U0637: Lost Communication With Hybrid/EV Battery Pack Coolant Control Valve B
The vehicle bus reports loss of communication with smart HV battery pack coolant control valve B. Coolant routing for the battery cooling loop cannot be commanded.
What U0637 means
U0637 is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Hybrid/EV Battery Pack Coolant Control Valve B on the vehicle’s data network.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Yes
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Bus wiring open or shortedMost likely
- 02Module without power or groundPossible
- 03Module failedPossible
Can I drive with U0637?
Have it checked before relying on the car.
High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
Why we rate it urgent
- High-voltage system fault: the car may shut down or refuse to start
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U0637
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U0637. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for U0636. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Bus wiring open or shorted; module without power or ground; module failed. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
U0637 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- High-voltage battery coolant valve B
- Vehicle bus wiring
U0637 FAQ
What does U0637 mean?
U0637 means “Lost Communication With Hybrid/EV Battery Pack Coolant Control Valve B”. The vehicle bus reports loss of communication with smart HV battery pack coolant control valve B. Coolant routing for the battery cooling loop cannot be commanded.
Is U0637 serious? Can I keep driving?
We rate U0637 as urgent severity. Have it checked before relying on the car. High-voltage faults can shut the drive system down without much warning. Do not open orange high-voltage components; this needs a trained technician.
What causes U0637?
The most common causes, from most to least likely: Bus wiring open or shorted; Module without power or ground; Module failed. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U0637?
Typical labor is about $65–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U0637 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U0637 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.