U066E: Lost Communication With Charge Air Cooler Temperature Sensor Bank 2
The vehicle bus reports loss of communication with smart charge air cooler (intercooler) temperature sensor on bank 2. Charge-air density correction switches to a substitute value.
What U066E means
U066E is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Charge Air Cooler Temperature Sensor Bank 2 on the vehicle’s data network. Bank 2 is the side of a V or flat engine opposite cylinder 1.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Bus wiring open or shortedMost likely
- 02Module without power or groundPossible
- 03Module failedPossible
Can I drive with U066E?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U066E
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U066E. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for U066D. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Bus wiring open or shorted; module without power or ground; module failed. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
U066E repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- CAC temp sensor bank 2
- Vehicle bus wiring
U066E FAQ
What does U066E mean?
U066E means “Lost Communication With Charge Air Cooler Temperature Sensor Bank 2”. The vehicle bus reports loss of communication with smart charge air cooler (intercooler) temperature sensor on bank 2. Charge-air density correction switches to a substitute value.
Is U066E serious? Can I keep driving?
We rate U066E as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes U066E?
The most common causes, from most to least likely: Bus wiring open or shorted; Module without power or ground; Module failed. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U066E?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U066E myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U066E clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.