U3011: Ignition Input Off
Fault on the ignition OFF input — module does not detect OFF state correctly. A communication loss with this module breaks any function relying on its data — diagnostic tools may show 'no response' and dependent modules can fall into limp mode.
What U3011 means
U3011 is a generic OBD-II network code in the module power group.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Ignition switch contacts wornMost likely
- 02Gateway module routing CAN messages incorrectlyLess likely
- 03CAN terminating resistor (120 Ω) drifted out of specLess likely
Can I drive with U3011?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U3011
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U3011. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Ignition input, Wiring) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Ignition switch contacts worn; gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
U3011 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Ignition input
- Wiring
U3011 FAQ
What does U3011 mean?
U3011 means “Ignition Input Off”. Fault on the ignition OFF input — module does not detect OFF state correctly. A communication loss with this module breaks any function relying on its data — diagnostic tools may show 'no response' and dependent modules can fall into limp mode.
Is U3011 serious? Can I keep driving?
We rate U3011 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes U3011?
The most common causes, from most to least likely: Ignition switch contacts worn; Gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U3011?
Typical labor is about $65–$250 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U3011 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will U3011 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.