U355B: Charge Air Cooler Outlet Pressure Sensor 2 Circuit
Generic fault on charge air cooler outlet pressure sensor 2 (after CAC, before stack on FCEV air path).
What U355B means
U355B is a generic OBD-II network code in the module power group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Sensor failedMost likely
- 02Gateway module routing CAN messages incorrectlyLess likely
- 03CAN terminating resistor (120 Ω) drifted out of specLess likely
Can I drive with U355B?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U355B
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U355B. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for U355A. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the cac outlet pressure sensor 2 and sensor wiring for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Sensor failed; gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
U355B repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- CAC outlet pressure sensor 2
- Sensor wiring
U355B FAQ
What does U355B mean?
U355B means “Charge Air Cooler Outlet Pressure Sensor 2 Circuit”. Generic fault on charge air cooler outlet pressure sensor 2 (after CAC, before stack on FCEV air path).
Is U355B serious? Can I keep driving?
We rate U355B as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes U355B?
The most common causes, from most to least likely: Sensor failed; Gateway module routing CAN messages incorrectly; CAN terminating resistor (120 Ω) drifted out of spec. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U355B?
Typical labor is about $125–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U355B myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U355B clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.