1998 Lincoln Navigator recalls

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Risk: DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

Remedy: SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL, THE SPEED CONTROL DEACTIVATION SWITCH MAY OVERHEAT, SMOKE, OR BURN.

Risk: A FIRE AT THE SWITCH COULD OCCUR.

Remedy: BY LETTER DATED SEPTEMBER 12, 2005, OWNERS WERE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED. OWNERS WHO HAVE HAD THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED THAT PARTS WILL BE AVAILABLE AND ADVISED TO MAKE AN APPOINTMENT TO RECONNECT THE SPEED CONTROL BEGINNING IN FEBRUARY 2006. OWNERS WHO DID NOT HAVE THEIR SPEED CONTROL DEACTIVATED ARE BEING NOTIFIED TO HAVE THEIR SYSTEM REMEDIED BEGINNING IN FEBRUARY 2006. OWNERS ARE URGED TO AVAIL THEMSELVES OF THE FREE DISCONNECT SERVICE AS SOON AS POSSIBLE BECAUSE OF THE SIGNIFICANT RISK OF FIRE. OWNERS MAY CONTACT FORD AT 1-800-392-3673. (NOTE: ALSO SEE RECALLS 05V017 AND 06V286)

VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES. THE TRAILER HITCH ASSEMBLY TO THE FRAME ATTACHING BOLTS COULD LOSE THE CLAMP LOAD.

Risk: THE TRAILER HITCH COULD THEN SEPARATE FROM THE VEHICLE.

Remedy: DEALERS WILL REPLACE THE TRAILER HITCH MOUNTING BOLTS AND NUT PLATES.

VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES AND LIGHT DUTY PICKUP TRUCKS. THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE.

Risk: THIS CAN RESULT IN THE LOOSENING OF LUG NUTS, STUD FATIGUE FAILURE, AND THE POTENTIAL FOR A WHEEL SEPARATION FROM THE VEHICLE, INCREASING THE RISK OF A VEHICLE CRASH.

Remedy: OWNERS OF THESE VEHICLES WILL BE RECEIVING TWO NOTIFICATIONS. THE FIRST NOTIFICATION, WHICH BEGAN IN MAY 1998, WILL PROVIDE AN INTERIM REPAIR PROCEDURE UNTIL PARTS BECOME AVAILABLE. THIS INTERIM PROCEDURE CAN BE COMPLETED BY OWNERS OR THEIR DEALERS. IT SPECIFIES THAT THE LUG NUT TORQUE MUST BE VERIFIED TO BE 100 LBS. THEN THE LUG NUTS NEED TO BE TIGHTENED AN ADDITIONAL 1/8 TO 1/4 TURN MORE. THERE WILL BE A SECOND OWNER NOTIFICATION, WHICH IS EXPECTED TO BEGIN JULY 20, 1998, UNDER WHICH DEALERS WILL INSPECT THE WHEEL STUDS AND REPLACE THE WHEEL LUG NUTS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TEXT AND/OR GRAPHICS FOR THE VEHICLE HEADLAMP AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Risk: IF THE HEADLAMP ASSEMBLIES ARE REPLACED, CUSTOMERS MAY BE CONFUSED BY THE AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES CAUSING THE HEADLAMPS TO BE IMPROPERLY AIMED.

Remedy: OWNER GUIDES CONTAINING REVISED AIMING INSTRUCTIONS WILL BE MAILED TO OWNERS OF THESE VEHICLES.

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. IF THE AUTOMATIC TRANSMISSION SHIFT CABLE ASSEMBLY WAS NOT FULLY ATTACHED TO THE STEERING COLUMN BRACKET, THE SHIFT CABLE ASSEMBLY CAN COME OUT OF THE BRACKET. THE VEHICLE OPERATOR WOULD THEN NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITIONS INTO THE PARK POSITION EVEN THOUGH THE GEAR SHIFT SELECTOR WOULD INDICATE "PARK."

Risk: THE CONDITION WOULD NOT ALLOW A DISENGAGEMENT OF THE TRANSMISSION FROM THE PARK POSITION OR AFFECT PROPER NEUTRAL START SWITCH OPERATION. UNINTENDED VEHICLE MOVEMENT COULD OCCUR IF THE PARKING BRAKE WAS NOT SET.

Remedy: DEALERS WILL MAKE THE PROPER ATTACHMENT OF THE TRANSMISSION SHIFT CONTROL CABLE TO THE STEERING COLUMN BRACKET AND ADD A TIE STRAP TO THAT CONNECTION.