B0900: Wiper Motor Front Circuit
A fault has been detected in the front wiper motor circuit.
What B0900 means
B0900 is a generic OBD-II body code in the other body group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Warning light or symbol related to the affected system
- Comfort or safety function impaired
Common causes
- 01Wiper motor failureMost likely
- 02Motor overload from frozen wipersPossible
- 03Wiper relay failurePossible
Can I drive with B0900?
Generally yes.
This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
Why we rate it low
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose B0900
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just B0900. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the front wiper motor and wiper relay for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Wiper motor failure; motor overload from frozen wipers; wiper relay failure. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
B0900 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Front wiper motor
- Wiper relay
- Body control module
B0900 FAQ
What does B0900 mean?
B0900 means “Wiper Motor Front Circuit”. A fault has been detected in the front wiper motor circuit.
Is B0900 serious? Can I keep driving?
We rate B0900 as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
What causes B0900?
The most common causes, from most to least likely: Wiper motor failure; Motor overload from frozen wipers; Wiper relay failure. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix B0900?
Typical labor is about $65–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix B0900 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will B0900 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.