B0910: Wiper Motor Rear Circuit
A fault has been detected in the rear wiper motor circuit.
What B0910 means
B0910 is a generic OBD-II body code in the other body group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Warning light or symbol related to the affected system
- Comfort or safety function impaired
Common causes
- 01Rear wiper motor failureMost likely
Can I drive with B0910?
Generally yes.
This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
Why we rate it low
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose B0910
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just B0910. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the rear wiper motor and body control module for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Rear wiper motor failure. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
B0910 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Yes, with a scan tool
Needs a scan tool and some experience with testing.
Parts and systems involved
- Rear wiper motor
- Body control module
B0910 FAQ
What does B0910 mean?
B0910 means “Wiper Motor Rear Circuit”. A fault has been detected in the rear wiper motor circuit.
Is B0910 serious? Can I keep driving?
We rate B0910 as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient to restore the affected feature.
What causes B0910?
The most common causes, from most to least likely: Rear wiper motor failure. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix B0910?
Typical labor is about $65–$315 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix B0910 myself?
DIY difficulty is moderate. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will B0910 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.