C0853: Active Damping Control Rear Right
The rear right adjustable damper reports an electrical fault.
What C0853 means
C0853 is a generic OBD-II chassis code in the other chassis group.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- ABS warning light on
- ESC/stability control deactivated
- Possible reduced brake assist
- Speedometer may behave erratically
Common causes
- 01Damper solenoid coil openMost likely
- 02Wiring chafePossible
Can I drive with C0853?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Usually lights the ABS, traction or stability warning instead of the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose C0853
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just C0853. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Active damper RR, Damper solenoid, Suspension control module) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Damper solenoid coil open; wiring chafe. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
C0853 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Active damper RR
- Damper solenoid
- Suspension control module
C0853 FAQ
What does C0853 mean?
C0853 means “Active Damping Control Rear Right”. The rear right adjustable damper reports an electrical fault.
Is C0853 serious? Can I keep driving?
We rate C0853 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes C0853?
The most common causes, from most to least likely: Damper solenoid coil open; Wiring chafe. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix C0853?
Typical labor is about $190–$625 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix C0853 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will C0853 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.