P0219: Engine Overspeed Condition
The ECU recorded an engine speed above the manufacturer's redline limit. Typical causes are missed downshifts, mis-shifts on a manual gearbox, or runaway diesel events. The code is informational but may trigger fuel cut-off and protective derate.
What P0219 means
P0219 is a generic OBD-II powertrain code in the fuel & air group.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Missed downshift on manual transmissionMost likely
- 02Crankshaft sensor signal spikeLess likely
Can I drive with P0219?
Generally yes.
This fault is unlikely to affect how the car drives. Fix it when convenient.
Why we rate it low
- Does not normally turn on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0219
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0219. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Engine, Crankshaft position sensor) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Missed downshift on manual transmission; crankshaft sensor signal spike. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0219 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Yes, with a scan tool
Basic hand tools; a common first DIY job.
Parts and systems involved
- Engine
- Crankshaft position sensor
P0219 FAQ
What does P0219 mean?
P0219 means “Engine Overspeed Condition”. The ECU recorded an engine speed above the manufacturer's redline limit. Typical causes are missed downshifts, mis-shifts on a manual gearbox, or runaway diesel events. The code is informational but may trigger fuel cut-off and protective derate.
Is P0219 serious? Can I keep driving?
We rate P0219 as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient.
What causes P0219?
The most common causes, from most to least likely: Missed downshift on manual transmission; Crankshaft sensor signal spike. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0219?
Typical labor is about $5–$125 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0219 myself?
DIY difficulty is easy. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P0219 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.