P0618: Alternative Fuel Control Module KAM Error
The control module for alternative fuel (CNG, LPG, hydrogen) reports a Keep-Alive-Memory error - persistent calibration values are corrupt or unreadable. Adaptive learning is reset.
What P0618 means
P0618 is a generic OBD-II powertrain code in the fuel & air group.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Possible limp mode or no-start
- Multiple follow-up faults across modules
- Reset/relearn may be needed after repair
Common causes
- 01KAM contents corruptedMost likely
- 02Module software outdated, reflash may resolveLess likely
- 03Supply voltage outside specificationLess likely
Can I drive with P0618?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P0618
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P0618. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Alternative fuel control module) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: KAM contents corrupted; module software outdated, reflash may resolve; supply voltage outside specification. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P0618 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Alternative fuel control module
P0618 FAQ
What does P0618 mean?
P0618 means “Alternative Fuel Control Module KAM Error”. The control module for alternative fuel (CNG, LPG, hydrogen) reports a Keep-Alive-Memory error - persistent calibration values are corrupt or unreadable. Adaptive learning is reset.
Is P0618 serious? Can I keep driving?
We rate P0618 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P0618?
The most common causes, from most to least likely: KAM contents corrupted; Module software outdated, reflash may resolve; Supply voltage outside specification. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P0618?
Typical labor is about $125–$375 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P0618 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P0618 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.