P2106: Throttle Actuator Control System — Forced Limited Power
The TAC monitor restricts maximum throttle opening as a safety response to a TAC fault. The vehicle can still be driven, but accelerator pedal travel is capped.
What P2106 means
P2106 is a generic OBD-II powertrain code in the fuel & air group.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Yes
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Check engine light on
- Reduced throttle response, possible limp mode
- Hesitation or surging
- Idle too high or too low
Common causes
- 01Underlying TAC fault triggers limitMost likely
- 02Pedal position sensor signal implausiblePossible
Can I drive with P2106?
Not recommended beyond getting it to a shop.
This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
Why we rate it urgent
- Can put the vehicle in limp mode (reduced power)
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2106
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2106. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P2104, P2105. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Throttle actuator control, ECM) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Underlying TAC fault triggers limit; pedal position sensor signal implausible. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2106 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Hard
- Good DIY job?
- Usually a shop job
Involved testing or major parts. Most owners use a shop.
Parts and systems involved
- Throttle actuator control
- ECM
P2106 FAQ
What does P2106 mean?
P2106 means “Throttle Actuator Control System — Forced Limited Power”. The TAC monitor restricts maximum throttle opening as a safety response to a TAC fault. The vehicle can still be driven, but accelerator pedal travel is capped.
Is P2106 serious? Can I keep driving?
We rate P2106 as urgent severity. Not recommended beyond getting it to a shop. This fault can put the engine or transmission in limp mode with reduced power, which can make merging and passing unsafe. Have it diagnosed as soon as possible.
What causes P2106?
The most common causes, from most to least likely: Underlying TAC fault triggers limit; Pedal position sensor signal implausible. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2106?
Typical labor is about $125–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2106 myself?
DIY difficulty is hard. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P2106 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.