P238A: Water in Fuel Sensor B Circuit
A general circuit fault on the secondary water-in-fuel sensor B - typically used on diesel systems with two filter housings (pre-pump and post-pump). The ECU loses water-detection feedback on this stage; risk of water reaching the high-pressure pump and injectors.
What P238A means
P238A is a generic OBD-II powertrain code in the fuel & air group. In plain English: the computer found an electrical fault in that circuit: an open, short or bad connection, or a failed component.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Open in sensor or wiringMost likely
Can I drive with P238A?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P238A
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P238A. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Fix other faults first
If other codes are stored, start with power-supply, sensor-circuit and communication codes. They can cause this code as a side effect.
- 3
Test the circuit
Inspect the wiring and connector at the water in fuel sensor b and fuel filter housing b for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Open in sensor or wiring. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P238A repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Easy
- Good DIY job?
- Yes, with a scan tool
Basic hand tools; a common first DIY job.
Parts and systems involved
- Water in fuel sensor B
- Fuel filter housing B
P238A FAQ
What does P238A mean?
P238A means “Water in Fuel Sensor B Circuit”. A general circuit fault on the secondary water-in-fuel sensor B - typically used on diesel systems with two filter housings (pre-pump and post-pump). The ECU loses water-detection feedback on this stage; risk of water reaching the high-pressure pump and injectors.
Is P238A serious? Can I keep driving?
We rate P238A as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P238A?
The most common causes, from most to least likely: Open in sensor or wiring. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P238A?
Typical labor is about $50–$175 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P238A myself?
DIY difficulty is easy. Many owners can handle it with a scan tool, a multimeter and basic hand tools. Always confirm the cause before buying parts.
Will P238A clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.