P26B5: Fuel Shutoff Valve B Control Circuit Performance/Stuck Off
The second fuel shutoff valve is commanded on but does not open.
What P26B5 means
P26B5 is a generic OBD-II powertrain code in the fuel & air group. In plain English: the signal is within electrical limits but doesn’t make sense compared with other readings, so the part or system isn’t performing as expected.
- Check engine light
- Usually on
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Not required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Valve seized closed by debrisMost likely
- 02Solenoid loses force from coil agingPossible
- 03Carbon or debris buildup preventing free movementLess likely
Can I drive with P26B5?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P26B5
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P26B5. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P26B3. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Test the circuit
Inspect the wiring and connector at the fuel shutoff valve b and solenoid for damage, corrosion or chafing. With a multimeter, check supply voltage, ground and signal against the specifications in the service manual for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Valve seized closed by debris; solenoid loses force from coil aging; carbon or debris buildup preventing free movement. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and drive the car under the conditions in the freeze-frame data to confirm it does not return.
P26B5 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Fuel shutoff valve B
- Solenoid
P26B5 FAQ
What does P26B5 mean?
P26B5 means “Fuel Shutoff Valve B Control Circuit Performance/Stuck Off”. The second fuel shutoff valve is commanded on but does not open.
Is P26B5 serious? Can I keep driving?
We rate P26B5 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P26B5?
The most common causes, from most to least likely: Valve seized closed by debris; Solenoid loses force from coil aging; Carbon or debris buildup preventing free movement. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P26B5?
Typical labor is about $125–$440 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P26B5 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P26B5 clear itself?
If the fault was intermittent, the warning may go off once the computer stops seeing it, but the code stays in memory. Fix the cause; clearing the code alone doesn’t repair anything.